Home / Buying guides

Buying guide: milliamp process clamp meters for 4 to 20 mA loops

A milliamp clamp around one wire of a 4 to 20 mA instrument loop, reading 12.00 mA, which is 50 percent of span
Beginner
How we wrote this: we haven't tested these instruments hands-on for this guide. Every figure comes from the manufacturer's own specifications, linked at the end. Models get discontinued and replaced, so check the current version before you buy. We don't earn anything if you buy one.

Most industrial sensors, such as pressure, flow, level and temperature transmitters, send their reading as a current between 4 and 20 mA. Checking that current normally means breaking the loop and putting a meter in series, which can upset the process. A milliamp process clamp meter reads the loop current by clamping around the wire, so the loop keeps running.

Why 4 to 20 mA?

A current loop isn't affected by the resistance of long cables, because the transmitter forces the same current all the way round. Using 4 mA, not 0 mA, as the bottom of the scale means a reading of 0 mA reveals a broken wire or a dead transmitter. The live zero also leaves enough current to power two-wire transmitters from the loop itself.

To convert a loop current to a percentage of the measured range: percent = (I − 4) ÷ 16 × 100. So 12 mA is 50%, and 8 mA is 25%.

Why an ordinary clamp meter won't do

A general-purpose clamp meter is built for amps and usually resolves 10 mA or 100 mA at best, which is coarse compared with the whole 16 mA span of a loop. A process clamp resolves 0.01 mA and is accurate to about 0.2% of reading on the 4 to 20 mA range.

What to look for

  • Measure only, or source and simulate as well. Measuring tells you what the loop is doing. Sourcing lets the meter supply a known current to test a controller input or a valve positioner. Simulating lets it act as a two-wire transmitter in a loop powered by something else.
  • Loop power. A built-in 24 V supply lets you power and test a transmitter on the bench, with no other kit.
  • Conductor size. The jaws are small, built for instrument cable cores. The Fluke 772's clamp takes conductors up to 4.5 mm across.
  • Interference. Because the meter is reading tiny magnetic fields, keep the jaws away from power cables carrying large currents, and follow the maker's zeroing instructions.

Fluke 771, 772 and 773 compared

FeatureFluke 771Fluke 772Fluke 773
Clamp measurement, 0 to 20.99 mA±(0.2% + 5 counts)±(0.2% + 5 counts)±(0.2% + 5 counts)
Clamp measurement, 21 to 100 mA±(1% + 5 counts)±(1% + 5 counts)±(1% + 5 counts)
In-series measurement, 0 to 24 mANoYes, ±(0.2% + 2 counts)Yes, ±(0.2% + 2 counts)
Source mA (up to 24 mA into 1 kΩ)NoYesYes
Simulate a transmitter (up to 50 V DC loop)NoYesYes
24 V loop powerNoYesYes
Measure DC volts (0 to 30 V)NoNoYes
Source DC volts (0 to 10 V)NoNoYes
Scaled mA output to a logging meterNoNoYes

All three resolve 0.01 mA and share the same IP40 rating and −10 to 50 °C operating range. Figures are from Fluke's datasheet for the 771, 772 and 773.

Which one?

  • Fluke 771 if you only need to read loop currents during fault-finding. It's the simplest and lightest.
  • Fluke 772 if you commission or calibrate loops. Sourcing, simulating and loop power cover most instrument technician jobs.
  • Fluke 773 if you also work with 0 to 10 V signals, or want to log a loop over time through another meter.

Need a general-purpose meter too? See our multimeter guide. Our guide to ADCs explains how a microcontroller can read a 4 to 20 mA signal through a precision resistor: 250 Ω turns 4 to 20 mA into 1 to 5 V.

Sources

The main references behind this guide. Numbers we worked out ourselves, such as the code outputs, come from running the code.