Home / Learn / Code for makers

The best microcontroller boards for beginners

New to this? Read from the top. Already know the basics? Jump to Going deeper for intermediate and advanced detail.

Three popular beginner boards side by side: an Arduino Uno, a Raspberry Pi Pico and an ESP32 development board
Beginner

There are hundreds of microcontroller boards, but three families cover almost every beginner's needs: the Arduino Uno, the Raspberry Pi Pico and boards built on the ESP32. All three are cheap, well documented and have huge communities. Here's how to choose.

Arduino Uno R4

The Uno is the classic beginner board, and the R4 is its current version. It comes in two models: the Minima, and the WiFi, which adds an ESP32-S3 module for wireless and a small LED matrix.

  • Chip: Renesas RA4M1 (32-bit Arm Cortex-M4) at 48 MHz, with 32 kB of RAM and 256 kB of flash.
  • Logic level: 5 V, like older Arduinos, so it works with lots of 5 V parts and shields.
  • Power: USB-C, or 6 to 24 V on the input jack or VIN pin.
  • Language: Arduino C++, in the Arduino IDE.

Best for: following tutorials and kits. Almost every beginner project online is written for an Uno. One thing to know: the R4's pins are rated for just 8 mA each, less than older Unos, so use transistors for anything beyond small LEDs.

Raspberry Pi Pico 2

The Pico 2 is Raspberry Pi's own microcontroller board. It's tiny, very cheap, and the easiest way into MicroPython.

  • Chip: RP2350 with two Arm Cortex-M33 cores (or two RISC-V cores, your choice) at 150 MHz, with 520 kB of RAM and 4 MB of flash.
  • Logic level: 3.3 V. The RP2350's digital pins can accept 5 V inputs, but only while the board is powered, and never the analogue pins (GP26 to GP28). The safe habit is to keep signals at 3.3 V.
  • Wireless: the Pico 2 W version adds Wi-Fi and Bluetooth.
  • Languages: MicroPython, CircuitPython, C/C++ and Arduino.

Best for: learning to code hardware in Python, and getting a lot of power for very little money.

ESP32 boards

ESP32 is a family of chips from Espressif, sold on boards from many makers. Built-in Wi-Fi and Bluetooth made it the favourite for internet-connected projects.

  • Chip: varies by model. The original ESP32 and the ESP32-S3 have two cores at up to 240 MHz. The ESP32-C3 and C6 are cheaper RISC-V versions with one main core.
  • Logic level: 3.3 V.
  • Wireless: Wi-Fi and Bluetooth on almost every model.
  • Languages: Arduino C++, MicroPython, and Espressif's own ESP-IDF.

Best for: smart home gadgets, sensors that report over Wi-Fi, and anything that talks to the internet. Because so many companies make ESP32 boards, quality and pin layouts vary, so buy from a known brand and use their pin diagram.

Quick comparison

Arduino Uno R4Pico 2 / Pico 2 WESP32 boards
Logic level5 V3.3 V3.3 V
Wi-FiWiFi model onlyPico 2 W onlyYes
Easiest languageArduino C++MicroPythonArduino C++
Tutorials and kitsThe mostLotsLots
PriceHighest of the threeLowestLow

Which should you buy?

  • Following a kit or a book? Get whatever it uses, most likely an Arduino Uno.
  • Want to learn Python? Get a Raspberry Pi Pico 2, or a Pico 2 W if you might want Wi-Fi later.
  • Building something that connects to the internet? Get an ESP32 board or a Pico 2 W.

Whichever you choose, add a breadboard, jumper wires, a few LEDs and resistors, and a multimeter. Then try Python for electronics beginners for your first programs.

Specifications are taken from the manufacturers' product information and may change with new board revisions, so check the official page for the board you buy.

Intermediate and advanced

Going deeper

Programmable I/O on the Pico

The RP2040 and RP2350 chips on Pico boards include PIO (programmable I/O) blocks: small state machines that run their own tiny programs, independent of the main processors. They can generate or read precise signals, such as driving addressable LEDs, extra serial ports or unusual protocols, without loading the CPU. MicroPython and the C SDK both support writing PIO programs.

Low power and sleep

For battery projects, the chip's sleep current matters less than the whole board's. Power LEDs, USB-to-serial chips and voltage regulators can draw milliamps even when the processor sleeps. ESP32 chips are popular for battery sensors because their deep sleep keeps a tiny low-power core and timer running, but you'll only get low currents from boards designed for it. Measure your actual board with a meter before trusting a datasheet figure.

Development tools beyond the beginner IDE

  • Pico SDK (C/C++) and ESP-IDF are the manufacturers' own toolkits, giving full control of the hardware.
  • PlatformIO, an extension for VS Code, builds Arduino and native projects for many boards with proper project management.
  • Rust has active embedded support for RP2040, RP2350 and ESP32 chips.
  • Debug probes (such as the Raspberry Pi Debug Probe) let you pause a running program, step through code and inspect variables, which is far quicker than adding print statements.

Security features

The RP2350 adds security features aimed at commercial products, including secure boot (only running firmware you've signed) and Arm TrustZone on its Cortex-M33 cores. ESP32 chips offer secure boot and flash encryption. Beginners can ignore these, but they matter if you're building something to sell.

Sources

The main references behind this guide. Numbers we worked out ourselves, such as the code outputs, come from running the code.